Your print says 16 gauge. Your wire box says .035. Your flowmeter reads CFH. Your laser welder wants millimeters, millimeters per second, liters per minute and percent.
None of that is hard. All of it is slow, and a wrong guess costs you a part. So we built THEO Shop Math: a free laser welding unit converter that turns shop numbers into machine numbers with one spin of a wheel. Use it right here, or take it to the bench in the THEO Toolbox app.
THEO Toolbox app · Free
Take Shop Math to the bench
One of the tools in the THEO Toolbox app, next to 80+ welding recipes, setup guides and training.

What Shop Math converts
- Thickness: sheet metal gauge, inches and millimeters, for stainless, steel, aluminum and galvanized. It shows the sheet at true size on your phone, so you can hold your part against the screen.
- Settings: wire feed speed and travel speed (mm/s to in/min), shielding gas flow (L/min to CFH) and wobble width (mm to inch).
- Power: percent to watts for every THEO MA1 model.
- Lingo: US names to ISO and EN names for wire sizes, welding positions, shielding gases, base metals and filler wires.
Sheet metal gauge to mm: one number, four thicknesses
Gauge is not a unit. It is a set of tables, and each metal has its own. 16 gauge stainless is 1.59 mm. 16 gauge aluminum is 1.29 mm. Same number, almost a third of a millimeter apart, and at laser welding heat inputs that gap is the difference between a clean seam and a hole.
Two rules keep you out of trouble: always ask which metal the gauge refers to, and remember that a higher gauge number means thinner sheet.
| Gauge | Steel (mm) | Stainless (mm) | Aluminum (mm) | Galvanized (mm) |
|---|---|---|---|---|
| 26 | 0.45 | 0.48 | 0.40 | 0.55 |
| 24 | 0.61 | 0.64 | 0.51 | 0.70 |
| 22 | 0.76 | 0.79 | 0.64 | 0.85 |
| 20 | 0.91 | 0.95 | 0.81 | 1.01 |
| 18 | 1.21 | 1.27 | 1.02 | 1.31 |
| 16 | 1.52 | 1.59 | 1.29 | 1.61 |
| 14 | 1.90 | 1.98 | 1.63 | 1.99 |
| 12 | 2.66 | 2.78 | 2.05 | 2.75 |
| 11 | 3.04 | 3.18 | 2.30 | 3.13 |
| 10 | 3.42 | 3.57 | 2.59 | 3.51 |
| 8 | 4.18 | 4.37 | 3.26 | 4.27 |
Nominal thickness. Real sheet varies within mill tolerance, so measure when it matters. Need inches, or a gauge that is not listed? Spin the wheel in Shop Math.
Wire feed and travel speed: mm/s to in/min
Multiply mm/s by 2.36 to get inches per minute. Divide in/min by 2.36 to go back.
| mm/s | in/min |
|---|---|
| 5 | 11.8 |
| 10 | 23.6 |
| 15 | 35.4 |
| 20 | 47.2 |
| 25 | 59.1 |
| 30 | 70.9 |
Watch the unit before you copy a number from a MIG chart. MIG wire feed runs in the hundreds of inches per minute. Laser wire feed is far slower, so a MIG habit typed into a laser welder will bury the joint in wire.
Shielding gas flow: L/min to CFH
Multiply L/min by 2.12 to get cubic feet per hour. Divide CFH by 2.12 to go back.
| L/min | CFH |
|---|---|
| 5 | 10.6 |
| 8 | 17.0 |
| 10 | 21.2 |
| 12 | 25.4 |
| 15 | 31.8 |
| 20 | 42.4 |
One more trap: a flowmeter is calibrated for one gas. Read argon on an argon scale.
Laser power: percent to watts
A THEO MA1 sets power as a percentage of the machine’s laser output. That makes a recipe easy to dial in, but 50 percent is not the same heat on every machine. If a spec, a colleague or a forum post gives you watts, convert before you pull the trigger.
| Setting | MA1-35 (800W) | MA1-45 (1200W) | MA1-65 (1500W) | MA1 ULTRA (2000W) |
|---|---|---|---|---|
| 25% | 200W | 300W | 375W | 500W |
| 50% | 400W | 600W | 750W | 1000W |
| 75% | 600W | 900W | 1125W | 1500W |
| 100% | 800W | 1200W | 1500W | 2000W |
The formula: watts = machine output × percent ÷ 100. Shop Math does it for any value and any MA1.
Same thing, two names: US and ISO lingo
Half of the confusion in a mixed shop is not numbers. It is names.
| What | US name | ISO / EN name |
|---|---|---|
| Filler wire size | .030 / .035 / .045 / 1/16 in | 0.8 / 0.9 / 1.2 / 1.6 mm |
| Flat groove weld | 1G | PA |
| Horizontal fillet weld | 2F | PB |
| Vertical up | 3G uphill | PF |
| Overhead groove weld | 4G | PE |
| Pure argon | Argon | I1 (ISO 14175) |
| Stainless sheet | 304 / 316L | 1.4301 / 1.4404 |
| Mild steel wire | ER70S-6 | G 3Si1 |
| Stainless wire | ER308LSi / ER316LSi | 19 9 L Si / 19 12 3 L Si |
Wire sizes are sold pairs, not exact conversions: .035 in wire and 0.9 mm wire are the same spool for practical purposes. Grades and filler classes are nearest matches, not identical specifications, so check the certificate when a job calls out a standard.
Shop Math lives in the THEO Toolbox app
Shop Math is one tool in the THEO Toolbox, the free app for THEO MA1 owners: 80+ welding recipes, setup guides, training, machine information and service support. The converter sits on your phone at the bench, next to the recipe you are about to run.
THEO Toolbox app · Free
Take Shop Math to the bench
Shop Math is one of the tools in the THEO Toolbox app, next to 80+ welding recipes, setup guides and training.

