Opens in a new tab

Support Hub

Frequently asked
questions

Answers on laser welding, laser cleaning, laser safety, the THEO Toolbox app and service.

Laser welding

What materials can the MA1 Handheld Laser Welding System weld?

The MA1 Series can weld a variety of materials including carbon steel, stainless steel, aluminum, non-ferrous metals, and other alloys. For detailed information on materials and weld penetration, please request the MA1 brochure.

What training is required to operate the MA1 Handheld Laser Welding System?

The MA1 Series is designed to be simple to learn and operate. Operators train in hours and reach proficiency in 1 to 2 weeks. Additionally, our solution partners provide hands-on training in system operation, welding, and safety to ensure users are fully equipped to use the MA1 Series effectively and safely.

What maintenance is required for the MA1 Handheld Laser Welding System?

The MA1 Series requires low maintenance, thanks to its air-cooled design which eliminates the need for frequent upkeep and reduces downtime.

What are the downsides of laser welding?

Laser welding needs a tighter joint fit-up than MIG welding: it is less forgiving of gaps between the parts. A handheld laser welder is also a Class 4 laser product, so the workplace needs a laser safety setup before the first weld.

More on laser welding safety

Can you laser weld vertically or overhead?

Yes. The MA1 Series welds in all positions: flat, horizontal, vertical and overhead. The welding position does not change the laser safety setup: the same rules apply in every position.

More on laser welding safety

What is wobble welding?

The laser beam swings from side to side across the joint while you move along it. A wider wobble gives a wider seam and bridges small gaps between the parts. On the MA1 Series you set the wobble width from 0 to 4 mm.

Is laser welding as strong as TIG or MIG welding?

A laser weld can meet the same strength requirements when penetration, joint fit-up and filler wire are right. As with any welding process, the strength depends on the setup. For load-bearing parts, qualify the welding procedure the same way you would for TIG or MIG.

Is laser welding faster than TIG?

Yes. THEO laser welding is up to 10x faster than TIG, depending on material, thickness and seam.

Laser welding and TIG compared

Laser cleaning

What is laser cleaning?

Laser cleaning removes rust, paint, oxides, grease, and other contaminants with short, high-energy pulses of light.

The laser beam hits the surface and is absorbed by the unwanted layer. That layer heats up instantly. A microscopic pressure zone forms between the contamination and the base material, lifting the unwanted material away.

Depending on the job, the contamination either vaporizes or breaks into fine particles that can be extracted safely.

The important part: when the process is set up correctly, the base material stays untouched.

That is what makes laser cleaning so useful. It gives you precise surface preparation without grinding, blasting, chemicals, or unnecessary damage. It works on stainless steel, aluminum, structural steel, copper, stone, and even select woods and plastics.

Why the base metal survives

Contamination and metal absorb the same light differently. Rust, paint and oxide layers take up much of the beam’s energy and heat up fast. Clean metal reflects more of it.

That gap gives every job a process window. Below a minimum energy per area, nothing comes off. Above a maximum, the beam starts to affect the metal underneath. Good cleaning sits between the two.

So “untouched” depends on the set-up. Too much energy or too many passes on one spot can still change the surface. Test on a sample of your part first.

The settings an operator controls

  • Pulse energy and pulse width. Energy per pulse, spread over the spot, sets how hard each pulse hits. Shorter pulses leave less time for heat to spread.
  • Pulse frequency. At the same average power, a higher frequency means less energy in each pulse. It changes both how hard and how often the surface is hit.
  • Spot size. Energy per area is pulse energy divided by spot area. A smaller spot raises it sharply.
  • Scan speed and fill spacing. These set how far apart the spots land and how much they overlap. More overlap puts more energy into the same area.

On the TM-300 you set these on the touchscreen or from the handle. Pulse width runs from 10 to 500 ns, scan speed goes up to 7,500 mm/s, and you choose among four scan patterns and three lenses. Presets cover common jobs.

Why the TM-300 uses pulsed MOPA

Some laser cleaners use continuous-wave technology. Constant heat input on the surface tends to melt the base material during cleaning, even when the contamination is fully removed.

The TM-300 uses MOPA pulsed laser technology instead. MOPA delivers short, controlled bursts of energy, the critical factor in cleaning without damage.

Where the removed material goes

The beam does not make dirt disappear. Part of the layer vaporizes, the rest leaves as fine particles. Together they form a plume above the work area that you should not breathe.

What is in it depends on what you remove. Old coatings can contain lead, chromates or zinc, or plastics that break down into harmful products. If you do not know the coating, have it analyzed before you start.

A fume extractor close to the cleaning head catches the plume where it forms. Where extraction alone cannot keep exposure low enough, add respiratory protection.

What laser cleaning is not good at

It is a precise tool, not a universal one.

  • Thick coatings. The beam removes a layer pass by pass. Thick paint systems take more passes, and more time.
  • Hidden surfaces. The beam travels in a straight line. Inside corners, bores and the back of a pipe are hard to reach.
  • Mirror finishes. Laser cleaning can raise surface roughness. If you need a polished finish, plan a follow-up step.

Safety basics

The TM-300 is a Class 4 laser product under EN 60825-1. It emits invisible near-infrared light at about 1064 nm. The beam and its reflections off the workpiece can injure eyes and skin and can start a fire.

  • Eyes. Wear EN 207:2017 certified laser safety goggles that cover the machine’s whole wavelength range. The operator manual specifies OD7+ for 1060 to 1070 nm. Three pairs come with the machine. Everyone near the machine wears the same protection.
  • Area. Work inside a defined laser area with warning signs at every entrance, keep combustible material out of it, and let nobody enter without protection.
  • Air. Extract the plume and wear respiratory protection.
  • People. Name one person who is responsible for laser safety.

Laser safety

What should I consider regarding safety?

While the ideal scenario for operating the MA1 Series is in a separate room, necessary safety can also be achieved with the use of laser safety curtains. Appropriate laser safety glasses are needed to protect the operator’s eyes during the welding process. We also recommend the use of gloves, long sleeves, and appropriate work boots for additional protection.

In some countries, including Germany, a designated laser safety officer is required within the company to ensure all safety protocols are being followed. It’s important to note that safety regulations can vary by region. Our solution expert partners are well-versed in local safety requirements and are more than happy to guide you through the safety protocols applicable in your specific region, ensuring your operations are both safe and compliant.

More on laser welding safety

What certifications does the MA1 Series hold?

The MA1 Series holds several certifications including EN 60204-1, EN 60825-1, ISO 11553-2, ISO 12100, EN IEC 61000-6-2, and EN IEC 61000-6-4.

Can I use a normal arc welding helmet for laser welding?

No. You need protection rated for the wavelength of your laser. THEO’s MA1 manual asks for EN 207:2017 certified laser safety goggles or a laser welding helmet that covers the whole wavelength range of the machine.

Do people standing nearby need protection too?

Yes. Everyone in the immediate vicinity of the machine wears the same protective equipment as the welder. Laser safety glasses

Glasses or helmet?

Both. THEO recommends laser safety glasses and a laser welding helmet: the helmet covers your face as well as your eyes, and the glasses protect your eyes whenever the helmet is off. Laser welding helmets

Is a respirator enough on its own?

No. A respirator protects the person wearing it. HSE asks for extraction first and respiratory protection where extraction alone is not enough, and THEO’s manuals require a fume extraction system. In a closed welding cell, extraction is mandatory.

Does laser cleaning need extraction?

Yes. The laser turns corrosion layers, paint and coatings into particles, fumes and vapors. DGUV’s guidance on laser cleaning asks for extraction that captures them as close to the point of origin as possible.

How far is the laser beam dangerous?

Much further than any workshop reaches. For the MA1 Series the calculated eye hazard distance (NOHD) is 127 m for the MA1-35, 156 m for the MA1-45, 174 m for the MA1-65 and 201 m for the MA1 ULTRA. That is why the beam has to be enclosed. The figures are from the MA1 Series operating parameters. Ask your laser safety officer about your setup.

THEO Toolbox app

Is the app really free?

Yes. The download is free and there are no in-app purchases.

Do I need a THEO to use it?

No. Basic welding recipes, THEO AI, the training and the community are open to everyone. With a registered THEO you also get the full welding recipes, your machine’s codes, documents, warranty status and service tickets.

Which phones does it run on?

iPhones with iOS 15.1 or later and Android phones. There is no iPad version.

Does the app control my welder?

No. The app does not connect to the machine. You read the recipe in the app and set the parameters on the machine.

Can I use it without a connection?

Saved welding recipes are available offline. Everything else needs a connection.

Where do I get help with the app?

Write to hello@theo.inc.

Service and support

What do I need for a service request?

Your machine’s serial number, your company and contact details, the country the machine is in, and a description of the problem. A photo helps. One serial number per request.

I bought from a THEO Partner. Who do I contact?

Start with your THEO Partner. They are your first contact for service, warranty and spare parts. If that does not solve it, send us a service request.

How long is the warranty?

Two years for the machine, the torch and the laser source if you register the machine, one year if you do not. Wear parts such as nozzles and protective windows are not covered. The warranty policy has the details.

How do I register my machine?

In the THEO Toolbox app: scan the code on the machine and follow the steps. Register your machine.

What is the activation code?

Your machine starts with a temporary code. You get the permanent code once you have completed the laser safety course in the THEO Academy.

Do you repair machines that are out of warranty?

Yes. Parts and labor are billed. The warranty policy lists the terms.

Is THEO AI a person?

No. THEO AI is an AI assistant trained on THEO’s manuals. If you need an engineer, send a service request.

Does THEO offer training, and where?

Yes. Most THEO Partners offer training and setup services when your machine is delivered. The THEO Academy has online courses, and the application labs in Gilching and Westborough offer hands-on sessions.

Where can I see or try a THEO machine?

At your THEO Partner, at the application labs in Gilching and Westborough, or with the trial offer.

Can’t find what you are looking for?

Your request

It takes about a minute. Fields with * are required.

We reply within one business day.